500ml

Showing all 8 results

  • Sale!

    Plastic Containers

    0.896.95 (ex vat)

    Used for mixing resins / topcoats and for cleaning tools in acetone. Unaffected by resin and can be reused by “cracking out” old resin build up. Lids can be supplied separately. Available in various sizes – 250ml / 500ml / 1lt / 2.5lt / 5lt / 10lt / 20lt / 15lt Black.

  • Sale!

    Calibrated Containers

    1.684.95 (ex vat)

    Perfect for measuring small amounts of Catalyst (Hardener) into Polyester or Epoxy Resins / Topcoats / Gelcoat.  Self Releasing – Can be re-used.

    • Conforms to ISO 7056 – 1981 (E) and BS 5404 Part 1.
    • Strong & flexible Polypropylene.
    • High translucency
    • Permanent graduations are moulded in for reproducibility.
    • Excellent chemical resistance.
    • Ideal for repair or laminating small areas
  • Sale!

    Summer Catalyst

    2.2157.44 (ex vat)

    All resins, gelcoats and topcoats must have catalyst (hardener) added to start the curing process. The amounts vary between 1% – 4% by weight depending on the required cure time and temperature. Please view our Catalyst mixing chart. Catalyst is a corrosive material and must be handled with special care. Dispensers are strongly recommended for safe and accurate use. See section on hazards. Please Note: In Order to comply with ADR Limited Quantity (Carriage of Dangerous Goods by Road) we can only ship in maximum units of 100ml eg: 1kg = 10 x 100ml. For large quantities, please contact us on +353 1 466 3786.

  • Catalyst

    2.9679.84 (ex vat)

    All resins, gelcoats and topcoats must have catalyst (hardener) added to start the curing process. The amounts vary between 1% – 4% by weight depending on the required cure time and temperature. Please view our Catalyst mixing chart. Catalyst is a corrosive material and must be handled with special care. Dispensers are strongly recommended for safe and accurate use. See section on hazards. Please Note: In order to comply with ADR Limited Quantity (Carriage of Dangerous Goods by Road) we can only ship in maximum units of 100ml eg: 1kg = 10 x 100ml. For large quantities, please contact us on +353 1 466 3786.

  • Sale! Plastic Squeeze Bottle

    Plastic Squeeze Bottle with Angled Straw

    2.984.87 (ex vat)

    Plastic Squeeze Bottle with Angled Straw for Dispensing Water

    Plastic wash bottles with Swan neck and a fine control tip. Ideal for washing down. Polypropylene screw closure with its angled stem and draw tube moulded in one piece for leak-proof applications

    Available in three sizes; 250ml, 500ml & 1000ml.

  • Sale!

    Winter Catalyst

    3.8499.95 (ex vat)

    Winter Catalyst (HBO-50) has been specifically designed for addition to CrysticCOOL Cure Resin and topcoats to start the curing process. The amounts vary between 1% – 4% by weight depending on the required cure time and temperature. It can also be added to other polyester resins / Gelcoats and Topcoats – but it will be similar to the summer catalyst cure times. Please view our Catalyst mixing chart. Catalyst is a corrosive material and must be handled with special care. Please Note: In order to comply with ADR Limited Quantity (Carriage of Dangerous Goods by Road) we can only ship in maximum units of 100ml eg: 1kg = 10 x 100ml containers. For large quantities, please contact us on +353 1 466 3786.

  • Sale!

    Solution MW Wax

    5.9539.80 (ex vat)

    A wax solution is added to the gelcoat mix at the rate of 2% where a completely tack free surface is required. It eliminates the surface tackiness caused by gelcoat when used as a final coating in sheating. Gelcoats applied with wax solution added will always needed to be abraded if further coats are required. (6% Strength) For General Health Information see section on hazards.

  • Sale!

    PVA Liquid Release Agent

    14.5378.64 (ex vat)

    PVA (polyvinyl alcohol) is a water-based liquid plastic that can be applied to waxed moulds to prevent moulded parts from sticking. PVA is not always required. Often laminators rely solely on mould release wax to create a surface contaminant on the mould that allows parts to be removed. However, on complicated moulds and on new moulds, when the risk of a part sticking in a mould is greatest, PVA can be applied over a waxed mould. For General Health Information see section on hazards.