Uncategorized

Showing 1–16 of 53 results

  • Dispensing Gun Crestabond

    Dispensing Gun Crestabond Bonding Agent

    Co-Axial Cartridges Manual Bi-Mixer Applicator

    • Manual bi-mixer applicator for co-axial cartridges (Crestabond)
    • For use with 380ml co-axial cartridges
    • Ideal for use where there is no access to compressed air
    • This range comprises simple budget tools through to the most powerful hand applicators available.CM 380/10 for 10:1 co-axial cartridges

     

    Read more
  • Sale!

    Summer Catalyst

    €2.21 – €21.32 (ex vat)

    All resins, gelcoats and topcoats must have catalyst (hardener) added to start the curing process. The amounts vary between 1% – 4% by weight depending on the required cure time and temperature. Please view our Catalyst mixing chart. Catalyst is a corrosive material and must be handled with special care. Dispensers are strongly recommended for safe and accurate use. See section on hazards. Please Note: In order to comply with ADR Limited Quantity (Carriage of Dangerous Goods by Road) we can only ship in maximum units of 100gm eg: 1kg = 10 x 100gm.  For larger quantities, 2.5kg, 5kg & 25kg  please contact us on + 353 1 466 3786 as we are unable to dispatch these sizes through our normal couriers, they require Haz Chem drivers. The goods are in stock and available for collection if required.

    Select options

  • Talc Fillers

    €2.50 – €39.80 (ex vat)

    Talc is an all-purpose inexpensive filler powder which is used to make resin into a bodyfiller. Also used in resin casting to reduce cost, shrinkage and heat generated by resin curing. Catalyst should be added before filler powder. Dark grey in colour.

    Select options
  • Placeholder

    Fillite

    €2.50 – €35.80 (ex vat)

    An excellent lightweight filler consisting of tiny hollow microspheres. Good for initial filling of large areas and easier than talc to sand down. Resin dramatically increases in volume when mixed with fillite. Also used for bedding down timber and steel ribs to the laminate.

    Select options
  • Sale!

    Winter Catalyst

    €3.84 – €37.09 (ex vat)

    Winter Catalyst (HBO-50) has been specifically designed for addition to CrysticCOOL Cure Resin and topcoats to start the curing process. The amounts vary between 1% – 4% by weight depending on the required cure time and temperature. It can also be added to other polyester resins / Gelcoats and Topcoats – but it will be similar to the summer catalyst cure times. Please view our Catalyst mixing chart. Catalyst is a corrosive material and must be handled with special care. Dispensers are strongly recommended for safe and accurate use. See section on hazards. Please Note: In order to comply with ADR Limited Quantity (Carriage of Dangerous Goods by Road) we can only ship in maximum units of 100gm eg: 1kg = 10 x 100gm.  For larger quantities, 2.5kg, 5kg & 25kg  please contact us on + 353 1 466 3786 as we are unable to dispatch these sizes through our normal couriers, they require Haz Chem drivers. The goods are in stock and available for collection if required.

    Select options

  • 165gm Surfboard Fabric

    €6.98 – €8.95 (ex vat)

    Perfect for sheathing Surfboards / Dinghy’s / Canoes / Model Building / Aviation. There are various other Fabrics available – Unidirectional / Biaxial / Quad axial / Double Biax stitched – Please contact us on 00353 1 466 3786

     

    Please select quantity range from dropdown menu (i.e. 1-4 mt) and enter the specific quantity you wish to order in the box beside the ‘add to basket’ button.

    Select options
  • Sale!

    210gm Glass Cloth (twin weave)

    €7.96 – €9.91 (ex vat)

    For use in general sheathing work, more common with model makers. Twill weave has good drapability, it is also a very ‘soft’ cloth that will laminate into awkward shapes and tight corners.

    Please select quantity range from dropdown menu (i.e. 1-4 mt) and enter the specific quantity you wish to order in the box beside the ‘add to basket’ button.

    Select options
  • Sale!

    Clear Polyester Gelcoat

    €12.50 – €174.96 (ex vat)

    High quality marine grade (Lloyds approved) brush Isophthalic gelcoat, which sets with a tacky surface on the exposed side. This gelcoat has excellent physical properties, water resistance and UV light stability. Used to produce the resin rich layer on the mouldings and is applied directly to the release agent. Available in a variety of RAL 840 colours.                                              Please Note: Catalyst (hardener) must also be added to the Topcoat in order for it to cure.Please contact +353 1 466 3786 for availability and price. For General Health Information see section on hazards.

    Select options
  • Sale!

    Clear Polyester Topcoat

    €13.86 – €189.62 (ex vat)

    Similar to gelcoat but with the addition of solution MW Wax. This enables the Gelcoat to be applied on the exposed side as a resin rich outer layer without a tacky finish. With its excellent physical properties, water resistance and UV light stability it is ideally suitable for the finishing coat to a surfboard or in wooden boat sheathing or gelcoat boat repairs. Available in a variety of RAL 840 Colours. Please note: if you require a Roofing Topcoat please look at our CrysticROOF Topcoat – Unlike other distributors our roofing topcoats are specifically designed for use on Roof / Balconies / Valleys and are very much easier to use than ordinary topcoat. – Check out the CrysticROOF Topcoat technical data sheet. Please Note: Catalyst (hardener) must also be added to the Topcoat in order for it to cure. For General Health Information see section on hazards.

    Select options
  • Sale!

    White Polyester Gelcoat

    €14.87 – €183.45 (ex vat)

    High quality marine grade (Lloyds approved) brush White Isophthalic gelcoat, which sets with a tacky surface on the exposed side. This gelcoat has excellent physical properties, water resistance and UV light stability. Used to produce the resin rich layer on the mouldings and is applied directly to the release agent. Please Note: Catalyst (hardener) must also be added to the Gelcoat in order for it to cure.For General Health Information see section on hazards.

    Select options
  • Sale!

    White Polyester Topcoat

    €14.95 – €196.80 (ex vat)

    Similar to gelcoat but with the addition of White pigment and solution MW wax. This enables the Gelcoat to be applied on the exposed side as a resin rich outer layer without a tacky finish. With its excellent physical properties, water resistance and UV light stability it is ideally suitable for the finishing coat to a variety of surfaces including boat repairs. Please Note: Catalyst (hardener) must also be added to the Topcoat in order for it to cure. For General Health Information see section on hazards.

    Select options
  • Sale!

    Easy Composites EL2 Epoxy Resin (Laminating Resin)

    €18.85 – €129.65 (ex vat)

    EL2 is a high performance epoxy laminating resin suitable for hand-layup of reinforcements such as carbon fibre, aramid and glass fibre. Its combination of mechanical performance, fast wet-out, easy handling and great value make EL2 a hugely popular choice in motorsport, boat-building, model-making and general composites.

    Sold as a kit (kit weight = combined weight of resin and hardener). Available to buy online in 500g, 1kg & 5kg kits.

    Select options
  • Sale!

    G4 Dampseal

    €59.75 (ex vat)

    A moisture curing single part polyurethane varnish ideal for sealing damp porous surfaces prior to using release agent. Used as damp proof floor sealing, pond sealing, sealing concrete prior to GRP sheathing where alkali in concrete can react with resins. Also used to improve the bond of GRP to metal.

    Select options
  • Sale!

    5sq meter Fibreglass Roofing Kit (medium duty)

    €145.53 (ex vat)

    Kit Contents:

    • 6kgs Polyester Resin (Lloyd’s Approved)
    • 5 meters 450gm/m2 Chopped Mat (medium duty)
    • 2.5kgs Polyester (dark grey) Roofing Topcoat
    • 400gm Catalyst

    This Fibreglass kit provide sufficient resin / topcoat and catalyst for a single layer (medium grade – 450gm/m2) of Chopped Strand Mat to cover the area required.

    The materials are specifically selected from our extensive range of products which gives you the assurance that when installed correctly, your roof will provide you with long term UV resistance and will remain watertight and maintenance free for many years.

    To order, just choose your roof size and use the links below to select your Trims/ Glassfibre Tape and Tool kit pack.

    For General Health Information see section on hazards.

    Add to basket
  • Sale!

    5sq meter Fibreglass Roofing Kit (heavy duty)

    €155.66 (ex vat)

    Kit Contents:+

    • 7.5kgs Polyester Resin (Lloyd’s) Approved
    • 5 meters 600gm/m2 Chopped Mat (heavy duty)
    • 2.5kgs Polyester (dark grey) Roofing Topcoat
    • 500gm Catalyst

    This Fibreglass kit provide sufficient resin / topcoat and catalyst for a single layer (600gm/m2) of Chopped Strand Mat to cover the area required.

    The materials are specifically selected from our extensive range of products which gives you the assurance that when installed correctly, your roof will provide you with long term UV resistance and will remain watertight and maintenance free for many years.

    To order, just choose your roof size and use the links below to select your Trims/ Glassfibre Tape and Tool kit pack.

    For General Health Information see section on hazards.

    Add to basket
  • Sale!

    10sq meter Fibreglass Roofing Kit (medium duty)

    €272.72 (ex vat)

     

    Kit Contents:

    • 12kgs Polyester Resin (Lloyd’s approved)
    • 10 meters 450gm/m2 Chopped Mat
    • 5kgs Polyester (dark grey) Roofing Topcoat
    • 800gm Catalyst

    This Fibreglass kit provide sufficient resin / topcoat and catalyst for a single layer (medium grade – 450gm/m2) of Chopped Strand Mat to cover the area required.

    The materials are specifically selected from our extensive range of products which gives you the assurance that when installed correctly, your roof will provide you with long term UV resistance and will remain watertight and maintenance free for many years.

    To order, just choose your roof size and use the links below to select your Trims/ Glassfibre Tape and Tool kit pack.

    For General Health Information see section on hazards.

    Add to basket