10 + Trims (3mt length)

Showing all 12 results

  • D260 Wall Fillet Trim

    15.9517.95 (ex vat)

    D260 is a fillet trim used to butt up against walls. It also provides an expansion gap around the edge of the roof. Sit the trim with the vertical against the wall, and the horizontal face on the deck. To join two lengths together simply overlap (by 50mm) using Fix ALL adhesive to bond together, then tape and resin over the joint with woven tape. Nail the D trim to the horizontal deck.

    All 3 metre lengths:

    • D260 – 120 x 60 x 80mm (in stock)

    Please Note: Our nationwide courier has notified us that they cannot carry any 3mt lengths (max 2mt). So the only option we have is to cut it to any length you require. If this is not acceptable, please contact us on 01 466 3786 to make alternative arrangements (which will incur extra costs).

  • E280 Expansion Joint (65 x 200mm)

    15.9517.95 (ex vat)

    E280 can be used for creating rolls on any ridge details, expansion joints on large roofs (50m2 or over) or to bridge GRP to felt roofs. Where necessary a sufficient gap in the deck should be cut and the trim then needs to be fixed to each end of the decking at 300mm centres. Ensure the join and fixing points are reinforced with Scott Bader’s woven glass tape (which is significantly stronger than chopped strand mat). The laminate can then be applied in the normal manner.

    C5 caps can be fixed by applying a 6-8mm bead of Fix ALL adhesive to the inside edge of the overlapping trim and bedded in. The trims can also be bonded together for longer lengths.

    The E280 trim is very useful when needing to bridge the GRP to a neighbouring felt roof. Where possible the adjoining felt should be lifted to slide the E280 underneath. Apply two 6-8mm beads of Fix-All adhesive on the base of the trim edge and on the top where the felt will sit. Use clout or ring nails to hold in place, while adhesive cures, any exposed edges should have a further bead applied to avoid water/ moisture ingress. The other side of the trim can be fixed and laminated in the normal manner.

    Please note that E280 is also referred to as expansion joint and ridge roll for pitched roofs.

    Please Note: Our nationwide courier has notified us that they cannot carry any 3mt lengths (max 2mt). So the only option we have is to cut it to any length you require. If this is not acceptable, please contact us on 01 466 3786 to make alternative arrangements (which will incur extra costs).

  • ER40-30 Simulated Lead Rolled Joint

    15.9517.95 (ex vat)

    ER40/30 is used to simulate the appearance of raised rolled lead joints. The trims should be nailed to the roof deck, any nail heads or joints bandaged and the whole trim laminated over.

    Use the C6 closures to cap the ends – nail to the deck and use Fix ALL adhesive to secure to the ER40/30 trim.

    In 3 metre lengths:

    • ER40/30 – 50 x 40mm

    Please Note: Our nationwide courier has notified us that they cannot carry any 3mt lengths (max 2mt). So the only option we have is to cut it to any length you require. If this is not acceptable, please contact us on 01 466 3786 to make alternative arrangements (which will incur extra costs).

  • G150 External 90deg Angle Trim (75mm x 75mm)

    15.9517.95 (ex vat)

    These angled trims are used to cover any features that sit perpendicular to the main roof or any other laminated surface.

    The G range of external trims have the finished face on the outer face. The trims should be nailed, any joints/nail heads taped and resin covered as per usual.

    • G150 – 75mm x 75mm (Standard, and in stock – this is what we will ship)
    • G275 – 200mm x 75mm (in stock)

    Please Note: Our nationwide courier has notified us that they cannot carry any 3mt lengths (max 2mt). So the only option we have is to cut it to any length you require. If this is not acceptable, please contact us on 01 466 3786 to make alternative arrangements (which will incur extra costs).

  • G180 Gully trim – Expansion joint (15 x 140mm)

    15.9517.95 (ex vat)

    Use the G180 to allow for expansion on large roofs over 50m2. It will also act as an integral gutter to aid drainage. The roof deck will need to be cut to allow the trim to sit in the gap with the flanges of the trim sitting flush to the deck. Nail the trim down, then tape and laminate the trim following the usual process.

    G180 – 15 x 140mm

    Please Note: Our nationwide courier has notified us that they cannot carry any 3mt lengths (max 2mt). So the only option we have is to cut it to any length you require. If this is not acceptable, please contact us on 01 466 3786 to make alternative arrangements (which will incur extra costs).

  • G275 External 90 degree Angle Trim (200mm x 75mm)

    15.9517.95 (ex vat)

    These angled trims are used to cover any features that sit perpendicular to the main roof or any other laminated surface.

    The G range of external trims have the finished face on the outer face. The trims should be nailed, any joints/nail heads taped and resin covered as per usual.

    • G150 – 75mm x 75mm (Standard and in stock)
    • G275 – 200mm x 75mm (in stock – this is what we will ship)

    Please Note: Our nationwide courier has notified us that they cannot carry any 3mt lengths (max 2mt). So the only option we have is to cut it to any length you require. If this is not acceptable, please contact us on 01 466 3786 to make alternative arrangements (which will incur extra costs).

  • H150SR Zinc effect – Preformed Rib Detail (25mm x 10mm)

    15.9517.95 (ex vat)

    GRP Zinc Effect Flat and Pitch Roofing trim.

    H150SR simulated Zinc effect GRP Trim is a perfect low cost product for your architectural roof. It also looks great and gets the water off the roof quickly.

    To join two lengths together simply overlap (by 50mm) using Fix ALL adhesive to bond together, then tape and resin over the joint with woven tape. Nail the D trim to the horizontal deck.

    All 3 metre lengths:

    • H150SR Zinc Effect rib detail 25mm x 10mm (in stock)

    Please Note: Our nationwide courier has notified us that they cannot carry any 3mt lengths (max 2mt). So the only option we have is to cut it to any length you require. If this is not acceptable, please contact us on 01 466 3786 to make alternative arrangements (which will incur extra costs).

  • A200 Facia Trim (95 x 90mm)

    16.0017.95 (ex vat)

    Drip trims are fitted to the lowest edge of the roof where water will flow into the gutter. Two support battens should be fitted to the fascia to sit under the trim to allow a space for the gutter to fit behind the trim. Fix ALL adhesive should be used to bond the trim to the batten on the vertical face, and nails used to fix the horizontal face onto the roof decking.

    Don’t nail through the face of the trim – this will show through the final topcoat finish on the front face. To join two lengths together simply overlap (by 50mm) and slot two pieces together using Fix ALL adhesive to bond together, then tape and resin over the joint with woven tape.

    Fitted to the roof edges to allow drainage into the gutter.

    • A170 (75 x 84mm)
    • A200 (95 x 90mm) – (Standard and in stock – this is what we will ship)
    • A250 (95 x 140mm) – (In stock – please phone 01 466 3786 to purchase)
    • A200 (90 x 90mm) – (same A200, but with drip return)

    Please Note: Our nationwide courier has notified us that they cannot carry any 3mt lengths (max 2mt). So the only option we have is to cut it to any length you require. If this is not acceptable, please contact us on 01 466 3786 to make alternative arrangements (which will incur extra costs).

  • B260 Raised Edge Trim

    16.0017.95 (ex vat)

    Raised edge trims do not allow the water over the edge into gutters. They should be fitted on top of single battens that have been fixed to the fascia, as there doesn’t need to be a gap for a gutter to sit in. Fix ALL adhesive should be used to bond the trim to the batten on the vertical face, and nails used to fix the horizontal face onto the roof decking.

    Don’t nail through the face of the trim – this will show through the final topcoat finish on the front face. To join two lengths together simply overlap (by 50mm) and slot two pieces together using Fix ALL adhesive to bond together, then tape and resin over the joint with woven tape.

    All 3 metre lengths:

    • B240 (100 x 105mm)
    • B260 (130 x 125mm) (Standard and in stock – this is what we will ship)
    • B300 (110 x 175mm) (In stock – please ph: 01 466 3786 to purchase)

    Please Note: Our nationwide courier has notified us that they cannot carry any 3mt lengths (max 2mt). So the only option we have is to cut it to any length you require. If this is not acceptable, please contact us on 01 466 3786 to make alternative arrangements (which will incur extra costs).

  • C100 Simulated Lead Flashing

    16.0017.95 (ex vat)

    C trims are lengths of simulated lead flashing with different depths of face. These trims should not be covered with topcoat, as they have a finished face already to simulated lead. The C trims should be slotted into a pre-chased mortar joint in the brickwork (approx 35-45mm deep), and sealed in with clear silicone. Fix ALL adhesive should also be used on the back of the C trims to bond to the D trim that they sit on top of.

    All 3 metre lengths:

    • C100 – 35 x 100mm (Standard and in stock)
    • C150 – 35 x 150mm

    Please Note: Our nationwide courier has notified us that they cannot carry any 3mt lengths (max 2mt). So the only option we have is to cut it to any length you require. If this is not acceptable, please contact us on 01 466 3786 to make alternative arrangements (which will incur extra costs).

  • H150 Internal Angle Trim (75mm x 75mm)

    16.0017.95 (ex vat)

    These angled trims are used to cover any features that sit perpendicular to the main roof or any other laminated surface.

    The H range of internal trims have the finished face on the inner face. The trims should be nailed, any joints/nail heads taped and resin covered as per usual.

    • H150 – 75mm x 75mm (Standard and in stock – this is what will be delivered)
    • H275 – 200mm x 75mm (in stock)

    Please Note: Our nationwide courier has notified us that they cannot carry any 3mt lengths (max 2mt). So the only option we have is to cut it to any length you require. If this is not acceptable, please contact us on 01 466 3786 to make alternative arrangements (which will incur extra costs) or you could organise collection yourself.

  • H275 Internal Angle Trim (200mm x 75mm)

    16.0017.95 (ex vat)

    These angled trims are used to cover any features that sit perpendicular to the main roof or any other laminated surface.

    The H range of internal trims have the finished face on the inner face. The trims should be nailed, any joints/nail heads taped and resin covered as per usual.

    • H150 – 75mm x 75mm (Standard and in stock)
    • H275 – 200mm x 75mm (in stock – this is what will be delivered)

    Please Note: Our nationwide courier has notified us that they cannot carry any 3mt lengths (max 2mt). So the only option we have is to cut it to any length you require. If this is not acceptable, please contact us on 01 466 3786 to make alternative arrangements (which will incur extra costs) or you could organise collection yourself.