5kg

Showing 1–16 of 21 results

  • Catalyst

    1.9749.95 (ex vat)

    All resins, gelcoats and topcoats must have catalyst (hardener) added to start the curing process. The amounts vary between 1% – 4% by weight depending on the required cure time and temperature. Please view our Catalyst mixing chart. Catalyst is a corrosive material and must be handled with special care. Dispensers are strongly recommended for safe and accurate use. See section on hazards. Please Note: In order to comply with ADR Limited Quantity (Carriage of Dangerous Goods by Road) we can only ship in maximum units of 100ml eg: 1kg = 10 x 100ml. For large quantities, please contact us on +353 1 466 3786.

  • Summer Catalyst

    1.9748.50 (ex vat)

    All resins, gelcoats and topcoats must have catalyst (hardener) added to start the curing process. The amounts vary between 1% – 4% by weight depending on the required cure time and temperature. Please view our Catalyst mixing chart. Catalyst is a corrosive material and must be handled with special care. Dispensers are strongly recommended for safe and accurate use. See section on hazards. Please Note: In Order to comply with ADR Limited Quantity (Carriage of Dangerous Goods by Road) we can only ship in maximum units of 100ml eg: 1kg = 10 x 100ml. For large quantities, please contact us on +353 1 466 3786.

  • Winter Catalyst

    1.9759.85 (ex vat)

    Winter Catalyst (HBO-50) has been specifically designed for addition to CrysticCOOL Cure Resin and topcoats to start the curing process. The amounts vary between 1% – 4% by weight depending on the required cure time and temperature. It can also be added to other polyester resins / Gelcoats and Topcoats – but it will be similar to the summer catalyst cure times. Please view our Catalyst mixing chart. Catalyst is a corrosive material and must be handled with special care. Please Note: In order to comply with ADR Limited Quantity (Carriage of Dangerous Goods by Road) we can only ship in maximum units of 100ml eg: 1kg = 10 x 100ml containers. For large quantities, please contact us on +353 1 466 3786.

  • Talc Fillers

    2.5039.80 (ex vat)

    Talc is an all-purpose inexpensive filler powder which is used to make resin into a bodyfiller. Also used in resin casting to reduce cost, shrinkage and heat generated by resin curing. Catalyst should be added before filler powder. Dark grey in colour.

  • Sale! polyester resin glassfibre.ie online shop

    Polyester Resin

    7.50109.50 (ex vat)

    Polyester Resin is suitable for Boat building/ Car/ Tractor/ Truck/ Pond & Marine repairs. Can be bought online with next day delivery. Lloyds approved. Used in conjunction with Chopped strand mat and other reinforcements. Other types of Polyester and Epoxy Resins are available, like Roofing/ Casting etc.

    This is a general purpose top quality orthophthalic polyester resin which requires the addition of 1% – 4% MEKP Catalyst / hardener (included up to 10kgs) to make it set. See our catalyst mixing chart. Suitable for making car bodies, boats, general repair work. Lloyds approved. Used in conjunction with Chopped strand mat and other reinforcements. Please note: if you require a Roofing resin, visit our CrysticROOF Resins. Unlike other distributors our roofing resins are specifically designed and very much easier to use than GP Resins – Please check out the CrysticROOF technical data sheet. For General Health Information see section on hazards.

  • Carborundum grit – Slip Resistant Grit

    7.98119.75 (ex vat)

    Carborundum grit is used to produce an extremely hardwearing slip resistant surface. It can come pre-mixed Slip Resistant Topcoat or sprinkled onto a final flocoat or resin surface while still wet (pre-mixed looks better). Especially useful on workboats where abrasion to the GRP laminate is caused by ropes and chains. Also on Roofs/ Balconies and steps where a degree of slip resistant is required. Supplied as Grade 24 (medium grade). Other grades (Fine 36 grade & Course 12 grade) are available on request.

  • Sale!

    White Virgin Aluminium Oxide – Slip Resistant Grit

    8.90128.60 (ex vat)

    White Aluminium Oxide

    White aluminum oxide is used as a durable and efficient non-skid media. The white color minimizes the ‘darkening’ or ‘dilution’ of colored coatings. The angular shape of aluminum oxide makes it an ideal grit for use in a variety of non-skid applications including concrete floors, stairs and boat decks. The inert nature of aluminum oxide allows it to be used with a variety of coating materials. The hardness of the grit particle creates a durable, long-lasting surface that requires minimal maintenance.

    The grit is used to produce an extremely hardwearing slip resistant surface. It can come pre-mixed or sprinkled onto a final flocoat or resin surface while still wet (pre-mixed looks better). Especially useful on workboats where abrasion to the GRP laminate is caused by ropes and chains. Also on Balconies and steps where a degree of slip resistant is required. Supplied as Grade 24 (medium grade).

  • Sale!

    6mm Chopped Strands

    8.9557.50 (ex vat)

    Supplied in 6mm lengths and used for reinforcing the Gelcoat in the mould / gap filling / polyester putty. Also used as a fillet “sprinkled” into sharp internal corners during laminating.

  • Sale!

    Clear Polyester Gelcoat

    10.89149.74 (ex vat)

    High quality marine grade (Lloyds approved) brush Isophthalic gelcoat, which sets with a tacky surface on the exposed side. This gelcoat has excellent physical properties, water resistance and UV light stability. Used to produce the resin rich layer on the mouldings and is applied directly to the release agent. Available in a variety of RAL 840 colours.                                              Please NoteCatalyst (hardener) must also be added to the Topcoat in order for it to cure.Please contact +353 1 466 3786 for availability and price. For General Health Information see section on hazards.

  • Sale!

    Clear Polyester Topcoat

    12.96165.00 (ex vat)

    Similar to gelcoat but with the addition of solution MW Wax. This enables the Gelcoat to be applied on the exposed side as a resin rich outer layer without a tacky finish. With its excellent physical properties, water resistance and UV light stability it is ideally suitable for the finishing coat to a surfboard or in wooden boat sheathing or gelcoat boat repairs. Available in a variety of RAL 840 Colours. Please note: if you require a Roofing Topcoat please look at our CrysticROOF Topcoat – Unlike other distributors our roofing topcoats are specifically designed for use on Roof / Balconies / Valleys and are very much easier to use than ordinary topcoat. – Check out the CrysticROOF Topcoat technical data sheet. Please Note: Catalyst (hardener) must also be added to the Topcoat in order for it to cure. For General Health Information see section on hazards.

  • Sale!

    White Polyester Gelcoat

    13.50159.75 (ex vat)

    High quality marine grade (Lloyds approved) brush White Isophthalic gelcoat, which sets with a tacky surface on the exposed side. This gelcoat has excellent physical properties, water resistance and UV light stability. Used to produce the resin rich layer on the mouldings and is applied directly to the release agent. Please NoteCatalyst (hardener) must also be added to the Gelcoat in order for it to cure.For General Health Information see section on hazards.

  • Sale!

    White Polyester Topcoat

    13.98189.75 (ex vat)

    Similar to gelcoat but with the addition of White pigment and solution MW wax. This enables the Gelcoat to be applied on the exposed side as a resin rich outer layer without a tacky finish. With its excellent physical properties, water resistance and UV light stability it is ideally suitable for the finishing coat to a variety of surfaces including boat repairs. Please Note: Catalyst (hardener) must also be added to the Topcoat in order for it to cure. For General Health Information see section on hazards.

  • Sale! Water Clear Casting Polyester Resin

    Water Clear Casting Polyester Resin + Hardener

    18.5069.80 (ex vat)

    Clear Casting Polyester Resin is a water clear polyester resin ideally suited to casting ornaments, making paperweights, preserve medical and biological specimens or making costume jewellery.

    If doing multiple pours of clear casting resin, great care should be taken in regards to the heat that is generated with each pour. Before each pour, it is best to ensure the first pour has cooled (and is cool to the touch) before adding the next batch of resin.

    Catalyst included. See our ‘Catalyst Mixing Chart‘. For General Health Information see section on hazards.

    Please view our GlassCast Epoxy Casting Resin which is more suitable for tabletops, bartops, decorative floor effects, furniture and creative projects.

  • Sale!

    Epoxy Filler – SP Microfibers 500gm

    23.50 19.86 (ex vat)

    SP Microfibres are very fine wood-cellulose fibres commonly used to create structural adhesives for bonding both wood and grp.

    Because any low viscosity resin system is readily absorbed into a porous surface such as wood, an unfilled adhesive may tend to give a ‘dry joint’. With their absorbent properties, microfibres can retain a significant quantity of adhesive within a joint and limit resin absorption into the surrounding surface, thus ensuring an adequate resin supply for adhesion. Where the strongest bond is required, e.g. timber scarf joints, microfibres should always be used in preference to hollow sphere-types of filler.

    For bonding parallel to the grain with lower density, lower strength timbers, such as cedar or obeche, a microballoon mix is often adequate, and is of lower density. Weight – 500gm

    Technical Details;

    Composition: Milled bleached cellulose wood pulp
    Appearance: White ‘fluffy’ fibrous consistency
    Particle Size: 200 – 300 microns
    Particle Density: Particles absorb resin
    Bulk Density: 100g/litre approx.

    Colloidal Silica + Microfibres + Epoxy = Adhesive Mix

    For General Health Information see section on hazards.

    Add to basket
  • Sale!

    CrysticROOF Resin

    22.70136.75 (ex vat)

    CrysticRoof Resin has been specifically formulated for ease of application and to leave a tack free finish suitable for adhesion with the topcoat. It also boasts a colour change system to show that catalyst addition has taken place. Features Low Styrene Emission technology (LSE) – minimising odours. It is speciffically designed for Roofing application. Price excludes MEKP Catalyst. For General Health Information see section on hazards.

  • Sale!

    CrysticCOOL Cure Resin

    22.70136.75 (ex vat)

    CrysticROOF COOLCure is a lower temperature curing resin designed for application in cold weather down to as low as 5°C. An Installer can lengthen the building season later in winter and earlier in spring by using CrysticROOF COOLCure resin. It has been specifically developed to have a quicker curing speed than the standard CrysticROOF Resin. For General Health Information see section on hazards.